Deutschland
Hersteller/ Fabrikant
IBK-FIBERTEC GMBH
Deutschland
GRP structural components for rotor blades Gone with the wind... Rotor blades of wind turbines are now too large to be transported over roads to construction sites. They are therefore manufactured in two parts and assembled at the construction site. The internal structural component is manufactured by IBK-Fibertec by means of a winding process. This is the inside blade of an E115 by Enercon: www.enercon.de www.wind-turbine-models.com
Angebot anfordernIBK-FIBERTEC GMBH
Deutschland
A worldwide success for IBK-Fibertec Professional antenna systems are installed all over the world on high transmitter masts and towers. As a radome (radar dome), GRP offers decisive advantages for transmitters: The highest degree of transparency in relation to electromagnetic radiation Protection of the antennas from environmental influences such as ice, snow, rain, wind and dirt Protection of antennas and brackets from corrosion Regardless of the weather conditions, the antenna systems can be inspected, upgraded and extended at any time.
Angebot anfordernIBK-FIBERTEC GMBH
Deutschland
Three times better For three key reasons, GRP for mobile phone masts is the optimal alternative to steel and reinforced concrete: 1. Low weight reduces material and logistics costs GRP masts weigh less than a third of reinforced concrete masts. This saves expensive access development in hard-to-reach areas, reduces the cost of foundations and minimises deployment costs, resulting in significant savings regarding material and logistics costs. 2. High degree of electromagnetic transparency GRP is transparent to electromagnetic waves. With this high degree of permeability, GRP is therefore the ideal material for the cladding of antennas. In addition, due to its minimal attenuation, it also allows for antenna installation inside the masts. 3. Extensive freedom from maintenance GRP masts are exceptionally resistant to weather and corrosion. Even in climatically demanding areas with high weathering requirements, regular costly maintenance is no longer required.
Angebot anfordernIBK-FIBERTEC GMBH
Deutschland
Resistant in all kinds of weather IBK has developed and manufactured a GRP support tower for its partner SPL for the coastal train in Ostend, Belgium. It is a worldwide innovation, since the mast provides both stability and insulation. Other advantages include corrosion resistance in the difficult weather conditions on the North Sea, as well as longevity. For the contact wire, insulators can be completely dispensed with, since the mast adequately acts as an insulator. www.powerlines-group.com
Angebot anfordernIBK-Fibertec konzipiert, berechnet und fertigt Bauteile aus Verbundwerkstoffen bevorzugt zur Aufnahme hoher Lasten. Als Fertigungsverfahren kommen Infusionstechnik, Handlaminate und Wickelverfahren zum Einsatz. Unsere Produkte: • Antennenmasten / Antennenzylinder • Kunststoffradome • Wickelrohre aus glasfaserverstärktem Kunststoff (GFK) • Ingenieurbüros für Tragwerksplanung • Fahrleitungsmasten • Ingenieurbüros für Kunststofftechnik • Ingenieurbüros für Schwingungsmesstechnik Mit unseren Produkten, Leistungen und Qualitäten sind wir ein international agierender Marktführer für GFK-Antennenzylinder und GFK-Mobilfunkmasten geworden.
Hersteller/ Fabrikant
Westring 40
33142 Büren - Deutschland
HOLCIM TECHNICAL SOLUTIONS AND PRODUCTS GMBH
Deutschland
Einzigartig in Europa! Aumaware / Bahnenware / Sheeting bis zu 3,10 m Breite aus EVM, EPDM, EPDM Trinkwasser, NBR, NR, MVQ, Silikon, FKM, CR, IIR Mit unserem Bereich Sheeting haben wir ein umfangreiches Produktspektrum an Bahnenware (bis 3,10 m Breite) und Plattenware aus allen gängigen Elastomeren, in einem Härtebereich von 25°- 90° Shore A und den Materialstärken von 0,5 mm – 8,0 mm. Auch Plattenware bis 60 mm in den Maßen 1,20m x 1,20m bieten wir an. Verschiedenste Zulassungen u.a. nach KTW, W 270 und VDE zeigen den hohen Qualitätsstandard unserer Materialien. Auch die Konformität bezüglich unterschiedlicher Automobil-Normen können wir gewährleisten. Hochspezialisierte Produkte für alle denkbaren Einsätze sind unsere Stärke. Mit unserem engagierten Team finden wir auch für Ihren Anwendungsfall eine passende Lösung. Entwicklung und Produktion: Mannheim (Deutschland)
Angebot anfordernJ. SCHWARZ GMBH
Deutschland
Polyethylen (PE), Polyoxymethylen (POM), Polyacetal: Technische Kunststoffe zur Verwendung als mechanische Bauteile, u. a. Gleitlager und Gleitschienen.
Angebot anfordernHOLCIM TECHNICAL SOLUTIONS AND PRODUCTS GMBH
Deutschland
NR / SBR / Silikon (MVQ), Fluorkautschuk (FKM), NBR, EPDM, EVM, CR Varianten mit diversen Zulassungen u.a. KTW, W270, WRAS, ACS, CLP, ...
Angebot anfordernHOLCIM TECHNICAL SOLUTIONS AND PRODUCTS GMBH
Deutschland
z.B. unsere Qualität: A-KT 90-00 - sehr harte Trinkwasser EPDM-Qualität, peroxidisch - Zulassung nach KTW-BWGL - Zulassung nach DIN EN 681-1/WA, WC - Zulassung nach WRAS (GB) und ACS (F) - Zulassung KIWA-ATA (NL), Belaqua (B) - kurzfristig bis 150°C einsetzbar z.B. unsere Qualität: A-KT- 55-00: - EPDM Trinkwasser-Qualität - peroxidisch vernetzt, konform der FDA 21 §177.2600 - Zulassung Elastomerleitlinie KTW - Zulassung Elastomerleitlinie W270 - Rückprallelastizität > 40% - PAK-Gehalt nach AfPS GS 2014: Kat. 1
Angebot anfordernMit nur einer Anfrage erhalten Sie mehrere Angebote von geprüften Anbietern